fmstr_example_rtt#
Overview#
Example application demonstrates the communication over SEGGER J-Link RTT interface. Example requires the FreeMASTER TCP/UDP communication plug-in to be used on the PC host side.
Supported Boards#
EVKB-IMXRT1050
Hardware requirements
Mini/micro USB cable
Target microcontroller board
Personal Computer
FreeMASTER 3.1.3 with Network plug-in updated for Segger RTT communication
Board settings
No special settings are required. By default this demo communicates over a SEGGER J-Link interface of the debugger USB connection.
Prepare the demo
Connect a USB cable between the host PC and the Debug USB port on the target board.
Compile and download the program to the target microcontroller.
Run and resume application execution when debugger stops in the main() function.
Connect with FreeMASTER
Run FreeMASTER, use the Connection Wizard or open Project Options.
Select network communication and configure the plug-in for RTT protocol.
Start communication, FreeMASTER loads the initial TSA Active Content links in the Welcome page.
Click the “FreeMASTER Demonstration Project (embedded in device)” in the Welcome page.
The demo is now running, you should be able to watch variable values and graphs.
More information
Read more information about FreeMASTER tool at http://www.nxp.com/freemaster. Feel free to ask questions and report issues at FreeMASTER’s community page at https://community.nxp.com/community/freemaster
MIMXRT1060-EVKB
Hardware requirements
Mini/micro USB cable
Target microcontroller board
Personal Computer
FreeMASTER 3.1.3 with Network plug-in updated for Segger RTT communication
Board settings
No special settings are required. By default this demo communicates over a SEGGER J-Link interface of the debugger USB connection.
Prepare the demo
Connect a USB cable between the host PC and the Debug USB port on the target board.
Compile and download the program to the target microcontroller.
Run and resume application execution when debugger stops in the main() function.
Connect with FreeMASTER
Run FreeMASTER, use the Connection Wizard or open Project Options.
Select network communication and configure the plug-in for RTT protocol.
Start communication, FreeMASTER loads the initial TSA Active Content links in the Welcome page.
Click the “FreeMASTER Demonstration Project (embedded in device)” in the Welcome page.
The demo is now running, you should be able to watch variable values and graphs.
More information
Read more information about FreeMASTER tool at http://www.nxp.com/freemaster. Feel free to ask questions and report issues at FreeMASTER’s community page at https://community.nxp.com/community/freemaster
MIMXRT1060-EVKC
Hardware requirements
Mini/micro USB cable
Target microcontroller board
Personal Computer
FreeMASTER 3.1.3 with Network plug-in updated for Segger RTT communication
Board settings
No special settings are required. By default this demo communicates over a SEGGER J-Link interface of the debugger USB connection.
Prepare the demo
Connect a USB cable between the host PC and the Debug USB port on the target board.
Compile and download the program to the target microcontroller.
Run and resume application execution when debugger stops in the main() function.
Connect with FreeMASTER
Run FreeMASTER, use the Connection Wizard or open Project Options.
Select network communication and configure the plug-in for RTT protocol.
Start communication, FreeMASTER loads the initial TSA Active Content links in the Welcome page.
Click the “FreeMASTER Demonstration Project (embedded in device)” in the Welcome page.
The demo is now running, you should be able to watch variable values and graphs.
More information
Read more information about FreeMASTER tool at http://www.nxp.com/freemaster. Feel free to ask questions and report issues at FreeMASTER’s community page at https://community.nxp.com/community/freemaster
EVK-MIMXRT1010
Hardware requirements
Mini/micro USB cable
Target microcontroller board
Personal Computer
FreeMASTER 3.1.3 with Network plug-in updated for Segger RTT communication
Board settings
No special settings are required. By default this demo communicates over a SEGGER J-Link interface of the debugger USB connection.
Prepare the demo
Connect a USB cable between the host PC and the Debug USB port on the target board.
Compile and download the program to the target microcontroller.
Run and resume application execution when debugger stops in the main() function.
Connect with FreeMASTER
Run FreeMASTER, use the Connection Wizard or open Project Options.
Select network communication and configure the plug-in for RTT protocol.
Start communication, FreeMASTER loads the initial TSA Active Content links in the Welcome page.
Click the “FreeMASTER Demonstration Project (embedded in device)” in the Welcome page.
The demo is now running, you should be able to watch variable values and graphs.
More information
Read more information about FreeMASTER tool at http://www.nxp.com/freemaster. Feel free to ask questions and report issues at FreeMASTER’s community page at https://community.nxp.com/community/freemaster
EVK-MIMXRT1015
Hardware requirements
Mini/micro USB cable
Target microcontroller board
Personal Computer
FreeMASTER 3.1.3 with Network plug-in updated for Segger RTT communication
Board settings
No special settings are required. By default this demo communicates over a SEGGER J-Link interface of the debugger USB connection.
Prepare the demo
Connect a USB cable between the host PC and the Debug USB port on the target board.
Compile and download the program to the target microcontroller.
Run and resume application execution when debugger stops in the main() function.
Connect with FreeMASTER
Run FreeMASTER, use the Connection Wizard or open Project Options.
Select network communication and configure the plug-in for RTT protocol.
Start communication, FreeMASTER loads the initial TSA Active Content links in the Welcome page.
Click the “FreeMASTER Demonstration Project (embedded in device)” in the Welcome page.
The demo is now running, you should be able to watch variable values and graphs.
More information
Read more information about FreeMASTER tool at http://www.nxp.com/freemaster. Feel free to ask questions and report issues at FreeMASTER’s community page at https://community.nxp.com/community/freemaster
EVK-MIMXRT1020
Hardware requirements
Mini/micro USB cable
Target microcontroller board
Personal Computer
FreeMASTER 3.1.3 with Network plug-in updated for Segger RTT communication
Board settings
No special settings are required. By default this demo communicates over a SEGGER J-Link interface of the debugger USB connection.
Prepare the demo
Connect a USB cable between the host PC and the Debug USB port on the target board.
Compile and download the program to the target microcontroller.
Run and resume application execution when debugger stops in the main() function.
Connect with FreeMASTER
Run FreeMASTER, use the Connection Wizard or open Project Options.
Select network communication and configure the plug-in for RTT protocol.
Start communication, FreeMASTER loads the initial TSA Active Content links in the Welcome page.
Click the “FreeMASTER Demonstration Project (embedded in device)” in the Welcome page.
The demo is now running, you should be able to watch variable values and graphs.
More information
Read more information about FreeMASTER tool at http://www.nxp.com/freemaster. Feel free to ask questions and report issues at FreeMASTER’s community page at https://community.nxp.com/community/freemaster
MIMXRT1024-EVK
Hardware requirements
Mini/micro USB cable
Target microcontroller board
Personal Computer
FreeMASTER 3.1.3 with Network plug-in updated for Segger RTT communication
Board settings
No special settings are required. By default this demo communicates over a SEGGER J-Link interface of the debugger USB connection.
Prepare the demo
Connect a USB cable between the host PC and the Debug USB port on the target board.
Compile and download the program to the target microcontroller.
Run and resume application execution when debugger stops in the main() function.
Connect with FreeMASTER
Run FreeMASTER, use the Connection Wizard or open Project Options.
Select network communication and configure the plug-in for RTT protocol.
Start communication, FreeMASTER loads the initial TSA Active Content links in the Welcome page.
Click the “FreeMASTER Demonstration Project (embedded in device)” in the Welcome page.
The demo is now running, you should be able to watch variable values and graphs.
More information
Read more information about FreeMASTER tool at http://www.nxp.com/freemaster. Feel free to ask questions and report issues at FreeMASTER’s community page at https://community.nxp.com/community/freemaster
MIMXRT1040-EVK
Hardware requirements
Mini/micro USB cable
Target microcontroller board
Personal Computer
FreeMASTER 3.1.3 with Network plug-in updated for Segger RTT communication
Board settings
No special settings are required. By default this demo communicates over a SEGGER J-Link interface of the debugger USB connection.
Prepare the demo
Connect a USB cable between the host PC and the Debug USB port on the target board.
Compile and download the program to the target microcontroller.
Run and resume application execution when debugger stops in the main() function.
Connect with FreeMASTER
Run FreeMASTER, use the Connection Wizard or open Project Options.
Select network communication and configure the plug-in for RTT protocol.
Start communication, FreeMASTER loads the initial TSA Active Content links in the Welcome page.
Click the “FreeMASTER Demonstration Project (embedded in device)” in the Welcome page.
The demo is now running, you should be able to watch variable values and graphs.
More information
Read more information about FreeMASTER tool at http://www.nxp.com/freemaster. Feel free to ask questions and report issues at FreeMASTER’s community page at https://community.nxp.com/community/freemaster
EVK-MIMXRT1064
Hardware requirements
Mini/micro USB cable
Target microcontroller board
Personal Computer
FreeMASTER 3.1.3 with Network plug-in updated for Segger RTT communication
Board settings
No special settings are required. By default this demo communicates over a SEGGER J-Link interface of the debugger USB connection.
Prepare the demo
Connect a USB cable between the host PC and the Debug USB port on the target board.
Compile and download the program to the target microcontroller.
Run and resume application execution when debugger stops in the main() function.
Connect with FreeMASTER
Run FreeMASTER, use the Connection Wizard or open Project Options.
Select network communication and configure the plug-in for RTT protocol.
Start communication, FreeMASTER loads the initial TSA Active Content links in the Welcome page.
Click the “FreeMASTER Demonstration Project (embedded in device)” in the Welcome page.
The demo is now running, you should be able to watch variable values and graphs.
More information
Read more information about FreeMASTER tool at http://www.nxp.com/freemaster. Feel free to ask questions and report issues at FreeMASTER’s community page at https://community.nxp.com/community/freemaster
MIMXRT1180-EVK
Hardware requirements
Mini/micro USB cable
Target microcontroller board
Personal Computer
FreeMASTER 3.1.3 with Network plug-in updated for Segger RTT communication
Board settings
No special settings are required. By default this demo communicates over a SEGGER J-Link interface of the debugger USB connection.
Prepare the demo
Connect a USB cable between the host PC and the Debug USB port on the target board.
Compile and download the program to the target microcontroller.
Run and resume application execution when debugger stops in the main() function.
Connect with FreeMASTER
Run FreeMASTER, use the Connection Wizard or open Project Options.
Select network communication and configure the plug-in for RTT protocol.
Start communication, FreeMASTER loads the initial TSA Active Content links in the Welcome page.
Click the “FreeMASTER Demonstration Project (embedded in device)” in the Welcome page.
The demo is now running, you should be able to watch variable values and graphs.
More information
Read more information about FreeMASTER tool at http://www.nxp.com/freemaster. Feel free to ask questions and report issues at FreeMASTER’s community page at https://community.nxp.com/community/freemaster
FRDM-IMXRT1152
Hardware requirements
USB-C cable
Target microcontroller board
Personal Computer
FreeMASTER 3.1.3 with Network plug-in updated for Segger RTT communication
Board settings
No special settings are required. By default this demo communicates over a SEGGER J-Link interface of the debugger USB connection.
Prepare the demo
Connect a USB cable between the host PC and the Debug USB port on the target board.
Compile and download the program to the target microcontroller.
Run and resume application execution when debugger stops in the main() function.
Connect with FreeMASTER
Run FreeMASTER, use the Connection Wizard or open Project Options.
Select network communication and configure the plug-in for RTT protocol.
Start communication, FreeMASTER loads the initial TSA Active Content links in the Welcome page.
Click the “FreeMASTER Demonstration Project (embedded in device)” in the Welcome page.
The demo is now running, you should be able to watch variable values and graphs.
More information
Read more information about FreeMASTER tool at http://www.nxp.com/freemaster. Feel free to ask questions and report issues at FreeMASTER’s community page at https://community.nxp.com/community/freemaster
FRDM-IMXRT1186
Hardware requirements
USB-C cable
Target microcontroller board
Personal Computer
FreeMASTER 3.1.3 with Network plug-in updated for Segger RTT communication
Board settings
No special settings are required. By default this demo communicates over a SEGGER J-Link interface of the debugger USB connection.
Prepare the demo
Connect a USB cable between the host PC and the Debug USB port on the target board.
Compile and download the program to the target microcontroller.
Run and resume application execution when debugger stops in the main() function.
Connect with FreeMASTER
Run FreeMASTER, use the Connection Wizard or open Project Options.
Select network communication and configure the plug-in for RTT protocol.
Start communication, FreeMASTER loads the initial TSA Active Content links in the Welcome page.
Click the “FreeMASTER Demonstration Project (embedded in device)” in the Welcome page.
The demo is now running, you should be able to watch variable values and graphs.
More information
Read more information about FreeMASTER tool at http://www.nxp.com/freemaster. Feel free to ask questions and report issues at FreeMASTER’s community page at https://community.nxp.com/community/freemaster
FRDM-IMXRT700
Hardware requirements
USB-C cable
Target microcontroller board
Personal Computer
FreeMASTER 3.1.3 with Network plug-in updated for Segger RTT communication
Board settings
No special settings are required. By default this demo communicates over a SEGGER J-Link interface of the debugger USB connection.
Prepare the demo
Connect a USB cable between the host PC and the Debug USB port on the target board.
Compile and download the program to the target microcontroller.
Run and resume application execution when debugger stops in the main() function.
Connect with FreeMASTER
Run FreeMASTER, use the Connection Wizard or open Project Options.
Select network communication and configure the plug-in for RTT protocol.
Start communication, FreeMASTER loads the initial TSA Active Content links in the Welcome page.
Click the “FreeMASTER Demonstration Project (embedded in device)” in the Welcome page.
The demo is now running, you should be able to watch variable values and graphs.
More information
Read more information about FreeMASTER tool at http://www.nxp.com/freemaster. Feel free to ask questions and report issues at FreeMASTER’s community page at https://community.nxp.com/community/freemaster
FRDM-KE17Z512
Hardware requirements
Mini/micro USB cable
Target microcontroller board
Personal Computer
FreeMASTER 3.1.3 with Network plug-in updated for Segger RTT communication
Board settings
No special settings are required. By default this demo communicates over a SEGGER J-Link interface of the debugger USB connection.
Prepare the demo
Connect a USB cable between the host PC and the Debug USB port on the target board.
Compile and download the program to the target microcontroller.
Run and resume application execution when debugger stops in the main() function.
Connect with FreeMASTER
Run FreeMASTER, use the Connection Wizard or open Project Options.
Select network communication and configure the plug-in for RTT protocol.
Start communication, FreeMASTER loads the initial TSA Active Content links in the Welcome page.
Click the “FreeMASTER Demonstration Project (embedded in device)” in the Welcome page.
The demo is now running, you should be able to watch variable values and graphs.
More information
Read more information about FreeMASTER tool at http://www.nxp.com/freemaster. Feel free to ask questions and report issues at FreeMASTER’s community page at https://community.nxp.com/community/freemaster
FRDM-MCXA153
Hardware requirements
USB-C cable
Target microcontroller board
Personal Computer
FreeMASTER 3.1.3 with Network plug-in updated for Segger RTT communication
Board settings
No special settings are required. By default this demo communicates over a SEGGER J-Link interface of the debugger USB connection.
Prepare the demo
Connect a USB cable between the host PC and the Debug USB port on the target board.
Compile and download the program to the target microcontroller.
Run and resume application execution when debugger stops in the main() function.
Connect with FreeMASTER
Run FreeMASTER, use the Connection Wizard or open Project Options.
Select network communication and configure the plug-in for RTT protocol.
Start communication, FreeMASTER loads the initial TSA Active Content links in the Welcome page.
Click the “FreeMASTER Demonstration Project (embedded in device)” in the Welcome page.
The demo is now running, you should be able to watch variable values and graphs.
More information
Read more information about FreeMASTER tool at http://www.nxp.com/freemaster. Feel free to ask questions and report issues at FreeMASTER’s community page at https://community.nxp.com/community/freemaster
FRDM-MCXA156
Hardware requirements
USB-C cable
Target microcontroller board
Personal Computer
FreeMASTER 3.1.3 with Network plug-in updated for Segger RTT communication
Board settings
No special settings are required. By default this demo communicates over a SEGGER J-Link interface of the debugger USB connection.
Prepare the demo
Connect a USB cable between the host PC and the Debug USB port on the target board.
Compile and download the program to the target microcontroller.
Run and resume application execution when debugger stops in the main() function.
Connect with FreeMASTER
Run FreeMASTER, use the Connection Wizard or open Project Options.
Select network communication and configure the plug-in for RTT protocol.
Start communication, FreeMASTER loads the initial TSA Active Content links in the Welcome page.
Click the “FreeMASTER Demonstration Project (embedded in device)” in the Welcome page.
The demo is now running, you should be able to watch variable values and graphs.
More information
Read more information about FreeMASTER tool at http://www.nxp.com/freemaster. Feel free to ask questions and report issues at FreeMASTER’s community page at https://community.nxp.com/community/freemaster
FRDM-MCXA174
Hardware requirements
USB-C cable
Target microcontroller board
Personal Computer
FreeMASTER 3.1.3 with Network plug-in updated for Segger RTT communication
Board settings
No special settings are required. By default this demo communicates over a SEGGER J-Link interface of the debugger USB connection.
Prepare the demo
Connect a USB cable between the host PC and the Debug USB port on the target board.
Compile and download the program to the target microcontroller.
Run and resume application execution when debugger stops in the main() function.
Connect with FreeMASTER
Run FreeMASTER, use the Connection Wizard or open Project Options.
Select network communication and configure the plug-in for RTT protocol.
Start communication, FreeMASTER loads the initial TSA Active Content links in the Welcome page.
Click the “FreeMASTER Demonstration Project (embedded in device)” in the Welcome page.
The demo is now running, you should be able to watch variable values and graphs.
More information
Read more information about FreeMASTER tool at http://www.nxp.com/freemaster. Feel free to ask questions and report issues at FreeMASTER’s community page at https://community.nxp.com/community/freemaster
FRDM-MCXA344
Hardware requirements
USB-C cable
Target microcontroller board
Personal Computer
FreeMASTER 3.1.3 with Network plug-in updated for Segger RTT communication
Board settings
No special settings are required. By default this demo communicates over a SEGGER J-Link interface of the debugger USB connection.
Prepare the demo
Connect a USB cable between the host PC and the Debug USB port on the target board.
Compile and download the program to the target microcontroller.
Run and resume application execution when debugger stops in the main() function.
Connect with FreeMASTER
Run FreeMASTER, use the Connection Wizard or open Project Options.
Select network communication and configure the plug-in for RTT protocol.
Start communication, FreeMASTER loads the initial TSA Active Content links in the Welcome page.
Click the “FreeMASTER Demonstration Project (embedded in device)” in the Welcome page.
The demo is now running, you should be able to watch variable values and graphs.
More information
Read more information about FreeMASTER tool at http://www.nxp.com/freemaster. Feel free to ask questions and report issues at FreeMASTER’s community page at https://community.nxp.com/community/freemaster
FRDM-MCXA346
Hardware requirements
USB-C cable
Target microcontroller board
Personal Computer
FreeMASTER 3.1.3 with Network plug-in updated for Segger RTT communication
Board settings
No special settings are required. By default this demo communicates over a SEGGER J-Link interface of the debugger USB connection.
Prepare the demo
Connect a USB cable between the host PC and the Debug USB port on the target board.
Compile and download the program to the target microcontroller.
Run and resume application execution when debugger stops in the main() function.
Connect with FreeMASTER
Run FreeMASTER, use the Connection Wizard or open Project Options.
Select network communication and configure the plug-in for RTT protocol.
Start communication, FreeMASTER loads the initial TSA Active Content links in the Welcome page.
Click the “FreeMASTER Demonstration Project (embedded in device)” in the Welcome page.
The demo is now running, you should be able to watch variable values and graphs.
More information
Read more information about FreeMASTER tool at http://www.nxp.com/freemaster. Feel free to ask questions and report issues at FreeMASTER’s community page at https://community.nxp.com/community/freemaster
FRDM-MCXA577
Hardware requirements
USB-C cable
Target microcontroller board
Personal Computer
FreeMASTER 3.1.3 with Network plug-in updated for Segger RTT communication
Board settings
No special settings are required. By default this demo communicates over a SEGGER J-Link interface of the debugger USB connection.
Prepare the demo
Connect a USB cable between the host PC and the Debug USB port on the target board.
Compile and download the program to the target microcontroller.
Run and resume application execution when debugger stops in the main() function.
Connect with FreeMASTER
Run FreeMASTER, use the Connection Wizard or open Project Options.
Select network communication and configure the plug-in for RTT protocol.
Start communication, FreeMASTER loads the initial TSA Active Content links in the Welcome page.
Click the “FreeMASTER Demonstration Project (embedded in device)” in the Welcome page.
The demo is now running, you should be able to watch variable values and graphs.
More information
Read more information about FreeMASTER tool at http://www.nxp.com/freemaster. Feel free to ask questions and report issues at FreeMASTER’s community page at https://community.nxp.com/community/freemaster
FRDM-MCXC162
Hardware requirements
USB-C cable
Target microcontroller board
Personal Computer
FreeMASTER 3.1.3 with Network plug-in updated for Segger RTT communication
Board settings
No special settings are required. By default this demo communicates over a SEGGER J-Link interface of the debugger USB connection.
Prepare the demo
Connect a USB cable between the host PC and the Debug USB port on the target board.
Compile and download the program to the target microcontroller.
Run and resume application execution when debugger stops in the main() function.
Connect with FreeMASTER
Run FreeMASTER, use the Connection Wizard or open Project Options.
Select network communication and configure the plug-in for RTT protocol.
Start communication, FreeMASTER loads the initial TSA Active Content links in the Welcome page.
Click the “FreeMASTER Demonstration Project (embedded in device)” in the Welcome page.
The demo is now running, you should be able to watch variable values and graphs.
More information
Read more information about FreeMASTER tool at http://www.nxp.com/freemaster. Feel free to ask questions and report issues at FreeMASTER’s community page at https://community.nxp.com/community/freemaster
FRDM-MCXC242
Hardware requirements
USB-C cable
Target microcontroller board
Personal Computer
FreeMASTER 3.1.3 with Network plug-in updated for Segger RTT communication
Board settings
No special settings are required. By default this demo communicates over a SEGGER J-Link interface of the debugger USB connection.
Prepare the demo
Connect a USB cable between the host PC and the Debug USB port on the target board.
Compile and download the program to the target microcontroller.
Run and resume application execution when debugger stops in the main() function.
Connect with FreeMASTER
Run FreeMASTER, use the Connection Wizard or open Project Options.
Select network communication and configure the plug-in for RTT protocol.
Start communication, FreeMASTER loads the initial TSA Active Content links in the Welcome page.
Click the “FreeMASTER Demonstration Project (embedded in device)” in the Welcome page.
The demo is now running, you should be able to watch variable values and graphs.
More information
Read more information about FreeMASTER tool at http://www.nxp.com/freemaster. Feel free to ask questions and report issues at FreeMASTER’s community page at https://community.nxp.com/community/freemaster
FRDM-MCXC444
Hardware requirements
USB-C cable
Target microcontroller board
Personal Computer
FreeMASTER 3.1.3 with Network plug-in updated for Segger RTT communication
Board settings
No special settings are required. By default this demo communicates over a SEGGER J-Link interface of the debugger USB connection.
Prepare the demo
Connect a USB cable between the host PC and the Debug USB port on the target board.
Compile and download the program to the target microcontroller.
Run and resume application execution when debugger stops in the main() function.
Connect with FreeMASTER
Run FreeMASTER, use the Connection Wizard or open Project Options.
Select network communication and configure the plug-in for RTT protocol.
Start communication, FreeMASTER loads the initial TSA Active Content links in the Welcome page.
Click the “FreeMASTER Demonstration Project (embedded in device)” in the Welcome page.
The demo is now running, you should be able to watch variable values and graphs.
More information
Read more information about FreeMASTER tool at http://www.nxp.com/freemaster. Feel free to ask questions and report issues at FreeMASTER’s community page at https://community.nxp.com/community/freemaster
FRDM-MCXE247
Hardware requirements
USB-C cable
Target microcontroller board
Personal Computer
FreeMASTER 3.1.3 with Network plug-in updated for Segger RTT communication
Board settings
No special settings are required. By default this demo communicates over a SEGGER J-Link interface of the debugger USB connection.
Prepare the demo
Connect a USB cable between the host PC and the Debug USB port on the target board.
Compile and download the program to the target microcontroller.
Run and resume application execution when debugger stops in the main() function.
Connect with FreeMASTER
Run FreeMASTER, use the Connection Wizard or open Project Options.
Select network communication and configure the plug-in for RTT protocol.
Start communication, FreeMASTER loads the initial TSA Active Content links in the Welcome page.
Click the “FreeMASTER Demonstration Project (embedded in device)” in the Welcome page.
The demo is now running, you should be able to watch variable values and graphs.
More information
Read more information about FreeMASTER tool at http://www.nxp.com/freemaster. Feel free to ask questions and report issues at FreeMASTER’s community page at https://community.nxp.com/community/freemaster
FRDM-MCXE31B
Hardware requirements
USB-C cable
Target microcontroller board
Personal Computer
FreeMASTER 3.1.3 with Network plug-in updated for Segger RTT communication
Board settings
No special settings are required. By default this demo communicates over a SEGGER J-Link interface of the debugger USB connection.
Prepare the demo
Connect a USB cable between the host PC and the Debug USB port on the target board.
Compile and download the program to the target microcontroller.
Run and resume application execution when debugger stops in the main() function.
Connect with FreeMASTER
Run FreeMASTER, use the Connection Wizard or open Project Options.
Select network communication and configure the plug-in for RTT protocol.
Start communication, FreeMASTER loads the initial TSA Active Content links in the Welcome page.
Click the “FreeMASTER Demonstration Project (embedded in device)” in the Welcome page.
The demo is now running, you should be able to watch variable values and graphs.
More information
Read more information about FreeMASTER tool at http://www.nxp.com/freemaster. Feel free to ask questions and report issues at FreeMASTER’s community page at https://community.nxp.com/community/freemaster
FRDM-MCXL255
Hardware requirements
USB-C cable
Target microcontroller board
Personal Computer
FreeMASTER 3.1.3 with Network plug-in updated for Segger RTT communication
Board settings
No special settings are required. By default this demo communicates over a SEGGER J-Link interface of the debugger USB connection.
Prepare the demo
Connect a USB cable between the host PC and the Debug USB port on the target board.
Compile and download the program to the target microcontroller.
Run and resume application execution when debugger stops in the main() function.
Connect with FreeMASTER
Run FreeMASTER, use the Connection Wizard or open Project Options.
Select network communication and configure the plug-in for RTT protocol.
Start communication, FreeMASTER loads the initial TSA Active Content links in the Welcome page.
Click the “FreeMASTER Demonstration Project (embedded in device)” in the Welcome page.
The demo is now running, you should be able to watch variable values and graphs.
More information
Read more information about FreeMASTER tool at http://www.nxp.com/freemaster. Feel free to ask questions and report issues at FreeMASTER’s community page at https://community.nxp.com/community/freemaster
FRDM-MCXN236
Hardware requirements
USB-C cable
Target microcontroller board
Personal Computer
FreeMASTER 3.1.3 with Network plug-in updated for Segger RTT communication
Board settings
No special settings are required. By default this demo communicates over a SEGGER J-Link interface of the debugger USB connection.
Prepare the demo
Connect a USB cable between the host PC and the Debug USB port on the target board.
Compile and download the program to the target microcontroller.
Run and resume application execution when debugger stops in the main() function.
Connect with FreeMASTER
Run FreeMASTER, use the Connection Wizard or open Project Options.
Select network communication and configure the plug-in for RTT protocol.
Start communication, FreeMASTER loads the initial TSA Active Content links in the Welcome page.
Click the “FreeMASTER Demonstration Project (embedded in device)” in the Welcome page.
The demo is now running, you should be able to watch variable values and graphs.
More information
Read more information about FreeMASTER tool at http://www.nxp.com/freemaster. Feel free to ask questions and report issues at FreeMASTER’s community page at https://community.nxp.com/community/freemaster
FRDM-MCXN947
Hardware requirements
Mini/micro USB cable
Target microcontroller board
Personal Computer
FreeMASTER 3.1.3 with Network plug-in updated for Segger RTT communication
Board settings
No special settings are required. By default this demo communicates over a SEGGER J-Link interface of the debugger USB connection.
Prepare the demo
Connect a USB cable between the host PC and the Debug USB port on the target board.
Compile and download the program to the target microcontroller.
Run and resume application execution when debugger stops in the main() function.
Connect with FreeMASTER
Run FreeMASTER, use the Connection Wizard or open Project Options.
Select network communication and configure the plug-in for RTT protocol.
Start communication, FreeMASTER loads the initial TSA Active Content links in the Welcome page.
Click the “FreeMASTER Demonstration Project (embedded in device)” in the Welcome page.
The demo is now running, you should be able to watch variable values and graphs.
More information
Read more information about FreeMASTER tool at http://www.nxp.com/freemaster. Feel free to ask questions and report issues at FreeMASTER’s community page at https://community.nxp.com/community/freemaster
FRDM-MCXN947T
Hardware requirements
Mini/micro USB cable
Target microcontroller board
Personal Computer
FreeMASTER 3.1.3 with Network plug-in updated for Segger RTT communication
Board settings
No special settings are required. By default this demo communicates over a SEGGER J-Link interface of the debugger USB connection.
Prepare the demo
Connect a USB cable between the host PC and the Debug USB port on the target board.
Compile and download the program to the target microcontroller.
Run and resume application execution when debugger stops in the main() function.
Connect with FreeMASTER
Run FreeMASTER, use the Connection Wizard or open Project Options.
Select network communication and configure the plug-in for RTT protocol.
Start communication, FreeMASTER loads the initial TSA Active Content links in the Welcome page.
Click the “FreeMASTER Demonstration Project (embedded in device)” in the Welcome page.
The demo is now running, you should be able to watch variable values and graphs.
More information
Read more information about FreeMASTER tool at http://www.nxp.com/freemaster. Feel free to ask questions and report issues at FreeMASTER’s community page at https://community.nxp.com/community/freemaster
FRDM-MCXW71
Hardware requirements
USB-C cable
Target microcontroller board
Personal Computer
FreeMASTER 3.1.3 with Network plug-in updated for Segger RTT communication
Board settings
No special settings are required. By default this demo communicates over a SEGGER J-Link interface of the debugger USB connection.
Prepare the demo
Connect a USB cable between the host PC and the Debug USB port on the target board.
Compile and download the program to the target microcontroller.
Run and resume application execution when debugger stops in the main() function.
Connect with FreeMASTER
Run FreeMASTER, use the Connection Wizard or open Project Options.
Select network communication and configure the plug-in for RTT protocol.
Start communication, FreeMASTER loads the initial TSA Active Content links in the Welcome page.
Click the “FreeMASTER Demonstration Project (embedded in device)” in the Welcome page.
The demo is now running, you should be able to watch variable values and graphs.
More information
Read more information about FreeMASTER tool at http://www.nxp.com/freemaster. Feel free to ask questions and report issues at FreeMASTER’s community page at https://community.nxp.com/community/freemaster
FRDM-RW612
Hardware requirements
USB-C cable
Target microcontroller board
Personal Computer
FreeMASTER 3.1.3 with Network plug-in updated for Segger RTT communication
Board settings
No special settings are required. By default this demo communicates over a SEGGER J-Link interface of the debugger USB connection.
Prepare the demo
Connect a USB cable between the host PC and the Debug USB port on the target board.
Compile and download the program to the target microcontroller.
Run and resume application execution when debugger stops in the main() function.
Connect with FreeMASTER
Run FreeMASTER, use the Connection Wizard or open Project Options.
Select network communication and configure the plug-in for RTT protocol.
Start communication, FreeMASTER loads the initial TSA Active Content links in the Welcome page.
Click the “FreeMASTER Demonstration Project (embedded in device)” in the Welcome page.
The demo is now running, you should be able to watch variable values and graphs.
More information
Read more information about FreeMASTER tool at http://www.nxp.com/freemaster. Feel free to ask questions and report issues at FreeMASTER’s community page at https://community.nxp.com/community/freemaster
MCX-W71-EVK
Hardware requirements
USB-C cable
Target microcontroller board
Personal Computer
FreeMASTER 3.1.3 with Network plug-in updated for Segger RTT communication
Board settings
No special settings are required. By default this demo communicates over a SEGGER J-Link interface of the debugger USB connection.
Prepare the demo
Connect a USB cable between the host PC and the Debug USB port on the target board.
Compile and download the program to the target microcontroller.
Run and resume application execution when debugger stops in the main() function.
Connect with FreeMASTER
Run FreeMASTER, use the Connection Wizard or open Project Options.
Select network communication and configure the plug-in for RTT protocol.
Start communication, FreeMASTER loads the initial TSA Active Content links in the Welcome page.
Click the “FreeMASTER Demonstration Project (embedded in device)” in the Welcome page.
The demo is now running, you should be able to watch variable values and graphs.
More information
Read more information about FreeMASTER tool at http://www.nxp.com/freemaster. Feel free to ask questions and report issues at FreeMASTER’s community page at https://community.nxp.com/community/freemaster
KW47-EVK
Hardware requirements
USB-C cable
Target microcontroller board
Personal Computer
FreeMASTER 3.1.3 with Network plug-in updated for Segger RTT communication
Board settings
No special settings are required. By default this demo communicates over a SEGGER J-Link interface of the debugger USB connection.
Prepare the demo
Connect a USB cable between the host PC and the Debug USB port on the target board.
Compile and download the program to the target microcontroller.
Run and resume application execution when debugger stops in the main() function.
Connect with FreeMASTER
Run FreeMASTER, use the Connection Wizard or open Project Options.
Select network communication and configure the plug-in for RTT protocol.
Start communication, FreeMASTER loads the initial TSA Active Content links in the Welcome page.
Click the “FreeMASTER Demonstration Project (embedded in device)” in the Welcome page.
The demo is now running, you should be able to watch variable values and graphs.
More information
Read more information about FreeMASTER tool at http://www.nxp.com/freemaster. Feel free to ask questions and report issues at FreeMASTER’s community page at https://community.nxp.com/community/freemaster
LPCXpresso54628
Hardware requirements
Mini/micro USB cable
Target microcontroller board
Personal Computer
FreeMASTER 3.1.3 with Network plug-in updated for Segger RTT communication
Board settings
No special settings are required. By default this demo communicates over a SEGGER J-Link interface of the debugger USB connection.
Prepare the demo
Connect a USB cable between the host PC and the Debug USB port on the target board.
Compile and download the program to the target microcontroller.
Run and resume application execution when debugger stops in the main() function.
Connect with FreeMASTER
Run FreeMASTER, use the Connection Wizard or open Project Options.
Select network communication and configure the plug-in for RTT protocol.
Start communication, FreeMASTER loads the initial TSA Active Content links in the Welcome page.
Click the “FreeMASTER Demonstration Project (embedded in device)” in the Welcome page.
The demo is now running, you should be able to watch variable values and graphs.
More information
Read more information about FreeMASTER tool at http://www.nxp.com/freemaster. Feel free to ask questions and report issues at FreeMASTER’s community page at https://community.nxp.com/community/freemaster
LPCXpresso55S06
Hardware requirements
Mini/micro USB cable
Target microcontroller board
Personal Computer
FreeMASTER 3.1.3 with Network plug-in updated for Segger RTT communication
Board settings
No special settings are required. By default this demo communicates over a SEGGER J-Link interface of the debugger USB connection.
Prepare the demo
Connect a USB cable between the host PC and the Debug USB port on the target board.
Compile and download the program to the target microcontroller.
Run and resume application execution when debugger stops in the main() function.
Connect with FreeMASTER
Run FreeMASTER, use the Connection Wizard or open Project Options.
Select network communication and configure the plug-in for RTT protocol.
Start communication, FreeMASTER loads the initial TSA Active Content links in the Welcome page.
Click the “FreeMASTER Demonstration Project (embedded in device)” in the Welcome page.
The demo is now running, you should be able to watch variable values and graphs.
More information
Read more information about FreeMASTER tool at http://www.nxp.com/freemaster. Feel free to ask questions and report issues at FreeMASTER’s community page at https://community.nxp.com/community/freemaster
LPCXpresso55S16
Hardware requirements
Mini/micro USB cable
Target microcontroller board
Personal Computer
FreeMASTER 3.1.3 with Network plug-in updated for Segger RTT communication
Board settings
No special settings are required. By default this demo communicates over a SEGGER J-Link interface of the debugger USB connection.
Prepare the demo
Connect a USB cable between the host PC and the Debug USB port on the target board.
Compile and download the program to the target microcontroller.
Run and resume application execution when debugger stops in the main() function.
Connect with FreeMASTER
Run FreeMASTER, use the Connection Wizard or open Project Options.
Select network communication and configure the plug-in for RTT protocol.
Start communication, FreeMASTER loads the initial TSA Active Content links in the Welcome page.
Click the “FreeMASTER Demonstration Project (embedded in device)” in the Welcome page.
The demo is now running, you should be able to watch variable values and graphs.
More information
Read more information about FreeMASTER tool at http://www.nxp.com/freemaster. Feel free to ask questions and report issues at FreeMASTER’s community page at https://community.nxp.com/community/freemaster
LPCXpresso55S28
Hardware requirements
Mini/micro USB cable
Target microcontroller board
Personal Computer
FreeMASTER 3.1.3 with Network plug-in updated for Segger RTT communication
Board settings
No special settings are required. By default this demo communicates over a SEGGER J-Link interface of the debugger USB connection.
Prepare the demo
Connect a USB cable between the host PC and the Debug USB port on the target board.
Compile and download the program to the target microcontroller.
Run and resume application execution when debugger stops in the main() function.
Connect with FreeMASTER
Run FreeMASTER, use the Connection Wizard or open Project Options.
Select network communication and configure the plug-in for RTT protocol.
Start communication, FreeMASTER loads the initial TSA Active Content links in the Welcome page.
Click the “FreeMASTER Demonstration Project (embedded in device)” in the Welcome page.
The demo is now running, you should be able to watch variable values and graphs.
More information
Read more information about FreeMASTER tool at http://www.nxp.com/freemaster. Feel free to ask questions and report issues at FreeMASTER’s community page at https://community.nxp.com/community/freemaster
LPCXpresso55S36
Hardware requirements
Mini/micro USB cable
Target microcontroller board
Personal Computer
FreeMASTER 3.1.3 with Network plug-in updated for Segger RTT communication
Board settings
No special settings are required. By default this demo communicates over a SEGGER J-Link interface of the debugger USB connection.
Prepare the demo
Connect a USB cable between the host PC and the Debug USB port on the target board.
Compile and download the program to the target microcontroller.
Run and resume application execution when debugger stops in the main() function.
Connect with FreeMASTER
Run FreeMASTER, use the Connection Wizard or open Project Options.
Select network communication and configure the plug-in for RTT protocol.
Start communication, FreeMASTER loads the initial TSA Active Content links in the Welcome page.
Click the “FreeMASTER Demonstration Project (embedded in device)” in the Welcome page.
The demo is now running, you should be able to watch variable values and graphs.
More information
Read more information about FreeMASTER tool at http://www.nxp.com/freemaster. Feel free to ask questions and report issues at FreeMASTER’s community page at https://community.nxp.com/community/freemaster
LPCXpresso55S69
Hardware requirements
Mini/micro USB cable
Target microcontroller board
Personal Computer
FreeMASTER 3.1.3 with Network plug-in updated for Segger RTT communication
Board settings
No special settings are required. By default this demo communicates over a SEGGER J-Link interface of the debugger USB connection.
Prepare the demo
Connect a USB cable between the host PC and the Debug USB port on the target board.
Compile and download the program to the target microcontroller.
Run and resume application execution when debugger stops in the main() function.
Connect with FreeMASTER
Run FreeMASTER, use the Connection Wizard or open Project Options.
Select network communication and configure the plug-in for RTT protocol.
Start communication, FreeMASTER loads the initial TSA Active Content links in the Welcome page.
Click the “FreeMASTER Demonstration Project (embedded in device)” in the Welcome page.
The demo is now running, you should be able to watch variable values and graphs.
More information
Read more information about FreeMASTER tool at http://www.nxp.com/freemaster. Feel free to ask questions and report issues at FreeMASTER’s community page at https://community.nxp.com/community/freemaster
MCX-W72-EVK
Hardware requirements
USB-C cable
Target microcontroller board
Personal Computer
FreeMASTER 3.1.3 with Network plug-in updated for Segger RTT communication
Board settings
No special settings are required. By default this demo communicates over a SEGGER J-Link interface of the debugger USB connection.
Prepare the demo
Connect a USB cable between the host PC and the Debug USB port on the target board.
Compile and download the program to the target microcontroller.
Run and resume application execution when debugger stops in the main() function.
Connect with FreeMASTER
Run FreeMASTER, use the Connection Wizard or open Project Options.
Select network communication and configure the plug-in for RTT protocol.
Start communication, FreeMASTER loads the initial TSA Active Content links in the Welcome page.
Click the “FreeMASTER Demonstration Project (embedded in device)” in the Welcome page.
The demo is now running, you should be able to watch variable values and graphs.
More information
Read more information about FreeMASTER tool at http://www.nxp.com/freemaster. Feel free to ask questions and report issues at FreeMASTER’s community page at https://community.nxp.com/community/freemaster
MIMXRT700-EVK
Hardware requirements
Mini/micro USB cable
Target microcontroller board
Personal Computer
FreeMASTER 3.1.3 with Network plug-in updated for Segger RTT communication
Board settings
No special settings are required. By default this demo communicates over a SEGGER J-Link interface of the debugger USB connection.
Prepare the demo
Connect a USB cable between the host PC and the Debug USB port on the target board.
Compile and download the program to the target microcontroller.
Run and resume application execution when debugger stops in the main() function.
Connect with FreeMASTER
Run FreeMASTER, use the Connection Wizard or open Project Options.
Select network communication and configure the plug-in for RTT protocol.
Start communication, FreeMASTER loads the initial TSA Active Content links in the Welcome page.
Click the “FreeMASTER Demonstration Project (embedded in device)” in the Welcome page.
The demo is now running, you should be able to watch variable values and graphs.
More information
Read more information about FreeMASTER tool at http://www.nxp.com/freemaster. Feel free to ask questions and report issues at FreeMASTER’s community page at https://community.nxp.com/community/freemaster
RD-RW612-BGA
Hardware requirements
Mini/micro USB cable
Target microcontroller board
Personal Computer
FreeMASTER 3.1.3 with Network plug-in updated for Segger RTT communication
Board settings
No special settings are required. By default this demo communicates over a SEGGER J-Link interface of the debugger USB connection.
Prepare the demo
Connect a USB cable between the host PC and the Debug USB port on the target board.
Compile and download the program to the target microcontroller.
Run and resume application execution when debugger stops in the main() function.
Connect with FreeMASTER
Run FreeMASTER, use the Connection Wizard or open Project Options.
Select network communication and configure the plug-in for RTT protocol.
Start communication, FreeMASTER loads the initial TSA Active Content links in the Welcome page.
Click the “FreeMASTER Demonstration Project (embedded in device)” in the Welcome page.
The demo is now running, you should be able to watch variable values and graphs.
More information
Read more information about FreeMASTER tool at http://www.nxp.com/freemaster. Feel free to ask questions and report issues at FreeMASTER’s community page at https://community.nxp.com/community/freemaster
KW47-LOC
Hardware requirements
USB-C cable
Target microcontroller board
Personal Computer
FreeMASTER 3.1.3 with Network plug-in updated for Segger RTT communication
Board settings
No special settings are required. By default this demo communicates over a SEGGER J-Link interface of the debugger USB connection.
Prepare the demo
Connect a USB cable between the host PC and the Debug USB port on the target board.
Compile and download the program to the target microcontroller.
Run and resume application execution when debugger stops in the main() function.
Connect with FreeMASTER
Run FreeMASTER, use the Connection Wizard or open Project Options.
Select network communication and configure the plug-in for RTT protocol.
Start communication, FreeMASTER loads the initial TSA Active Content links in the Welcome page.
Click the “FreeMASTER Demonstration Project (embedded in device)” in the Welcome page.
The demo is now running, you should be able to watch variable values and graphs.
More information
Read more information about FreeMASTER tool at http://www.nxp.com/freemaster. Feel free to ask questions and report issues at FreeMASTER’s community page at https://community.nxp.com/community/freemaster
MCXW72-LOC
Hardware requirements
USB-C cable
Target microcontroller board
Personal Computer
FreeMASTER 3.1.3 with Network plug-in updated for Segger RTT communication
Board settings
No special settings are required. By default this demo communicates over a SEGGER J-Link interface of the debugger USB connection.
Prepare the demo
Connect a USB cable between the host PC and the Debug USB port on the target board.
Compile and download the program to the target microcontroller.
Run and resume application execution when debugger stops in the main() function.
Connect with FreeMASTER
Run FreeMASTER, use the Connection Wizard or open Project Options.
Select network communication and configure the plug-in for RTT protocol.
Start communication, FreeMASTER loads the initial TSA Active Content links in the Welcome page.
Click the “FreeMASTER Demonstration Project (embedded in device)” in the Welcome page.
The demo is now running, you should be able to watch variable values and graphs.
More information
Read more information about FreeMASTER tool at http://www.nxp.com/freemaster. Feel free to ask questions and report issues at FreeMASTER’s community page at https://community.nxp.com/community/freemaster
FRDM-MCXA266
Hardware requirements
USB-C cable
Target microcontroller board
Personal Computer
FreeMASTER 3.1.3 with Network plug-in updated for Segger RTT communication
Board settings
No special settings are required. By default this demo communicates over a SEGGER J-Link interface of the debugger USB connection.
Prepare the demo
Connect a USB cable between the host PC and the Debug USB port on the target board.
Compile and download the program to the target microcontroller.
Run and resume application execution when debugger stops in the main() function.
Connect with FreeMASTER
Run FreeMASTER, use the Connection Wizard or open Project Options.
Select network communication and configure the plug-in for RTT protocol.
Start communication, FreeMASTER loads the initial TSA Active Content links in the Welcome page.
Click the “FreeMASTER Demonstration Project (embedded in device)” in the Welcome page.
The demo is now running, you should be able to watch variable values and graphs.
More information
Read more information about FreeMASTER tool at http://www.nxp.com/freemaster. Feel free to ask questions and report issues at FreeMASTER’s community page at https://community.nxp.com/community/freemaster
FRDM-MCXA366
Hardware requirements
USB-C cable
Target microcontroller board
Personal Computer
FreeMASTER 3.1.3 with Network plug-in updated for Segger RTT communication
Board settings
No special settings are required. By default this demo communicates over a SEGGER J-Link interface of the debugger USB connection.
Prepare the demo
Connect a USB cable between the host PC and the Debug USB port on the target board.
Compile and download the program to the target microcontroller.
Run and resume application execution when debugger stops in the main() function.
Connect with FreeMASTER
Run FreeMASTER, use the Connection Wizard or open Project Options.
Select network communication and configure the plug-in for RTT protocol.
Start communication, FreeMASTER loads the initial TSA Active Content links in the Welcome page.
Click the “FreeMASTER Demonstration Project (embedded in device)” in the Welcome page.
The demo is now running, you should be able to watch variable values and graphs.
More information
Read more information about FreeMASTER tool at http://www.nxp.com/freemaster. Feel free to ask questions and report issues at FreeMASTER’s community page at https://community.nxp.com/community/freemaster
FRDM-MCXW72
Hardware requirements
USB-C cable
Target microcontroller board
Personal Computer
FreeMASTER 3.1.3 with Network plug-in updated for Segger RTT communication
Board settings
No special settings are required. By default this demo communicates over a SEGGER J-Link interface of the debugger USB connection.
Prepare the demo
Connect a USB cable between the host PC and the Debug USB port on the target board.
Compile and download the program to the target microcontroller.
Run and resume application execution when debugger stops in the main() function.
Connect with FreeMASTER
Run FreeMASTER, use the Connection Wizard or open Project Options.
Select network communication and configure the plug-in for RTT protocol.
Start communication, FreeMASTER loads the initial TSA Active Content links in the Welcome page.
Click the “FreeMASTER Demonstration Project (embedded in device)” in the Welcome page.
The demo is now running, you should be able to watch variable values and graphs.
More information
Read more information about FreeMASTER tool at http://www.nxp.com/freemaster. Feel free to ask questions and report issues at FreeMASTER’s community page at https://community.nxp.com/community/freemaster
FRDM-MCXA287
Hardware requirements
USB-C cable
Target microcontroller board
Personal Computer
FreeMASTER 3.1.3 with Network plug-in updated for Segger RTT communication
Board settings
No special settings are required. By default this demo communicates over a SEGGER J-Link interface of the debugger USB connection.
Prepare the demo
Connect a USB cable between the host PC and the Debug USB port on the target board.
Compile and download the program to the target microcontroller.
Run and resume application execution when debugger stops in the main() function.
Connect with FreeMASTER
Run FreeMASTER, use the Connection Wizard or open Project Options.
Select network communication and configure the plug-in for RTT protocol.
Start communication, FreeMASTER loads the initial TSA Active Content links in the Welcome page.
Click the “FreeMASTER Demonstration Project (embedded in device)” in the Welcome page.
The demo is now running, you should be able to watch variable values and graphs.
More information
Read more information about FreeMASTER tool at http://www.nxp.com/freemaster. Feel free to ask questions and report issues at FreeMASTER’s community page at https://community.nxp.com/community/freemaster